What homeowners ask before they call
Honest answers about tile installation in Placer County homes.
Before the job starts
Do I need to remove the old tile before you arrive?
No — demo is part of what we handle. Removing existing tile, scraping adhesive residue, and preparing the substrate for new tile is included in the scope of work we quote. Attempting to demo yourself without knowing what is underneath can sometimes damage the substrate or waterproofing layer, which creates more work and cost. We prefer to assess the surface ourselves before anything is touched.
What is a decoupling membrane and do I need one?
A decoupling membrane is a thin layer — often a polyethylene mat like Schluter Ditra — installed between the subfloor and the tile. It isolates the tile layer from movement in the substrate below, which is especially important on wood subfloors. Without it, seasonal wood expansion and contraction can crack grout joints and eventually the tile itself. In Placer County's climate, where temperature swings between summer and winter are significant, we recommend decoupling membrane on most wood-subfloor installations.
How do I know if my subfloor can support large-format tile?
The industry standard for tile installation is that the subfloor must deflect no more than L/360 — meaning across any span of the floor, the flex under load should not exceed the span length divided by 360. For most large-format tile (anything over 15 inches in any dimension), we check the joist spacing, subfloor thickness, and span before recommending a tile size. If the floor has too much flex, we can reinforce it or recommend a smaller tile format that will perform reliably. We assess this during the walkthrough.
During the installation
Why can't I use the shower the same day the tile is set?
Thinset mortar — the adhesive that bonds tile to the substrate — needs time to cure before it can handle moisture and mechanical stress. Most polymer-modified thinsets require 24 hours before grouting, and the grout itself needs another 24 to 72 hours before water exposure, depending on the product. Rushing either window can compromise the bond and cause tiles to loosen or grout to fail prematurely. We give you a specific timeline based on the products used on your job.
What is back-buttering and when is it required?
Back-buttering means applying a thin layer of thinset directly to the back of the tile in addition to the mortar combed onto the substrate. It is required for natural stone tiles (which are often irregular on the back face), for large-format porcelain where full coverage is critical, and for any installation where the tile back has a deep relief pattern. The goal is 95% or greater mortar coverage on the tile back — a standard we follow on every wet-area installation to prevent hollow spots that can crack under load or trap moisture.
Can you match grout color to existing tile in an adjacent room?
We can get close, but grout color is affected by how it is mixed, the porosity of the tile it is applied to, and how it is cleaned during installation. An exact match to aged grout is rarely possible — grout changes color over time with use and cleaning products. If you are tiling an area that transitions to existing tile, we can work with you to choose a grout color that reads as intentional rather than mismatched. Bringing a tile sample to the walkthrough helps.
Materials and choices
What is the difference between ceramic and porcelain tile?
Both are fired clay products, but porcelain is fired at a higher temperature with a denser clay body, making it harder, less porous, and more resistant to moisture and wear. Ceramic is generally easier to cut and slightly less expensive. For bathroom floors, shower floors, and any exterior or high-moisture application, porcelain is the appropriate choice. Ceramic works well for wall applications and dry interior floors where budget is a consideration. We can walk you through the right material for your specific surface during the walkthrough.
Do natural stone tiles require sealing?
Most natural stone — marble, travertine, limestone, slate — is porous and should be sealed before grouting and again after installation is complete. The sealer penetrates the stone and reduces staining from grout haze, soap, and everyday use. How often the stone needs to be resealed depends on the stone type, the finish (polished stone is denser than honed), and the level of use. We seal all natural stone installations as part of the job, and we will tell you what maintenance schedule makes sense for the specific material you have chosen.
How much extra tile should I order beyond the measured area?
The standard overage recommendation is 10% for a straightforward rectangular room with a simple running bond or grid pattern. For diagonal or herringbone patterns, where more cuts are required, 15% is more appropriate. For natural stone with significant variation, or for any pattern that requires careful matching, 15 to 20% is safer. Ordering too little and having to source additional tile from a different production run can result in a visible color variation. We calculate the overage recommendation as part of our quote.
Have a question that is not covered here? Call us directly or send a message — we are available Mon-Sun, 7:00 AM to 10:00 PM.